Jamo PRO 9644a Manuel d'utilisateur télécharger pdf

128-6620A

1 of 8

SELECTABLE FEATURES

Note: The method of manual override can either be selected to operate from the valet switch or operate as

custom code. Be certain to place a check mark indicating the method used in the box located on

the last page of the owner's manual.

Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door

pin switch in order to begin the passive arming sequence.

RF Programmable Features :

Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps Default

1st Door L/UL 1 Sec. 3.5 Sec. 1 Sec L/Dbl. U/L 350mSul/1SL 1 Sec.

2nd Accy Lock Auto Lock On Auto Lock Off Auto Lock Off

3rd Accy. UL Auto UL Dr Auto UL All Auto UL Off Auto UL Off

4th Headlights On Arm On Disarm On Both Off Both

5th Passive Locks Passive Active Active

6th Passive/Active Arm Passive Arm Active Arm Active Arm

7th Voltage Sense Voltage Sense Hardwire Hardwire

8th Siren/Horn Siren/Horn Siren Only Horn Only Siren/Horn

9th Horn Chirp 10mS 16mS 30mS 16mS

10th Override Method Custom Code Valet Valet

11th Two Step Unlock On Off Off

12th Chirp Delete From Tx On Off Off

To program these selectable features;

Action System Response

Turn ignition on No response

Press and release the valet switch 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off Short chirp, then long chirp

First Then On 1 chirp = 1 second door locks

Press transmitter Lock button to change 2 chirps = 3.5 second door locks

Press transmitter Lock button to change 3 chirps = 1 sec. lock, dbl 1 sec. unlock

Second Press and release the valet switch 2 chirps = auto locks off

Press transmitter Lock button to change 1 chirp = auto locks on

Third Press and release the valet switch 3 chirps = auto unlock off

Press transmitter Lock button to change 1 chirp = auto unlock drivers door only

Press transmitter Lock button to change 2 chirps = auto unlock all doors

Fourth Press and release the valet switch 3 chirps = headlight output when arming and disarming

Press transmitter Lock button to change 4 chirps = headlight output off

Press transmitter Lock button to change 1 chirp = headlight output when arming

Press transmitter Lock button to change 2 chirps = headlight output when disarming

Model PRO 9644a

Installation Manual

Revision A: 3-23-04 Changed 1st Door L/UL specification

1 2 3 4 5 6 7 8

128-6620A 1
Model PRO 9644a 1

Résumé du contenu

Page 1 - Model PRO 9644a

128-6620A1 of 8SELECTABLE FEATURESNote: The method of manual override can either be selected to operate from the valet switch or operate ascustom code

Page 2

128-6620A2 of 8Page 2orFifth Press and release the valet switch 2 chirps = active locksPress transmitter Lock button to change 1 chirp = passive locks

Page 3

128-6620A3 of 8Page 3Dash Mounted LED:A small LED is included that will serve as a visual indicator of the alarm status. It should be installed in the

Page 4

128-6620A4 of 8Dark Blue Wire: DELAYED 300 mA PULSED OUTPUT / CHANNEL 3The dark blue wire pulses to ground via an independent RF channel from the keyc

Page 5

128-6620A5 of 8Page 5Note: This is a normally opened starter cut arrangement, and when power is removed from thesecurity system, the starter disable f

Page 6

128-6620A6 of 8Page 64 Pin White Connector: Shock Sensor (OPTIONAL)Route the red, black and green wires in the 4 pin white connector from the shock se

Page 7

128-6620A7 of 8optional relay. Connect the door side of the cut wire to terminal 30 of the optional relay added. Connect thevehicle side of the cut

Page 8

Commentaires sur ces manuels

Pas de commentaire

Jamo PRO 9644a Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Alarme de voiture Jamo PRO 9644a. JAMO PRO 9644A User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels